D-GC8 FUEL DISPENSER

D-GC8 FUEL DISPENSER

Pump Type :Optional

Inlet Pressure : >=54kPa.

Flow rate (L/min.) :55±5

Suction Distance (m) :6(verticalmente) / 50(orizzontalmente)

FlowMeter Type :Optional

Accuracy : ±0.2%

Motor Voltage(V): 110V/220V/380V,50Hz/60Hz

Capacity(hp):1HP(0.75kw)

Input Voltage : 110V/220V/380V,50Hz/60Hz

Nozzle :Auto Shut-off Nozzle

Environmental Condition : -40~~+55degree

Control Type : Solenold Vale Control Type

Preset :Function Provided(Small LCDIndicator)

Display(Counter) :Type LCD and Bright Backlight

Digit of Volume :0~~999,999(6 Digits),Decimal point can be changed

Digit of Amount :0~~999,999(6 Digits),Decimal point can be changed

Digit of Unit price : 0~~9999(4 Digits),Decimal point can be changed

Digit of Total Range :0~~99,999,999,99

Optional :Display Type LCD and Bright Backlight

Digit of Volume : 0~~99,999,999(8 Digits),Decimal point can be changed

Digit of Amount : 0~~99,999,999(8 Digits),Decimal point can be changed

Digit of Unit price : 0~~999999(6 Digits),Decimal point can be changed

Digit of Total Range :0~~99,999,999,99

Totalizer :1~~9,999,999

Hose :4.5m

Weight : 425kg

Dimension(L×W×H) : 1615 X 620 X2420(mm)

Dimension(L×W×H)Of Qty of Container :40ft: 26

operate motor. If it still don’t move or slowly run, electric circuit or motor should be inspected. If not the rotor of pump maybe locked. Carefully check and cleanse oil strainer. If failure still exists after the above inspection, overflow valve should be checkup. In case that valve core jam, shut down incompletely or lose in valve seat the oil in high pressure area overflow into negative area, resulting in no delivery or inefficient discharge. Taking out valve core and spring so as to clean dirty, inspect valve seat at same time. If valve seat is loose re-fix it fuel dispenser through oil-resistant glue or change a new pump. When find scrap of spring and graphite, washing overflow valve is must, changing broken parts if necessary. If found rotor is stuck there would be several reasons related, such as spring broken, long vane, vane segment, lose bolts at top cover, etc. reassembling after overcome these reasons. Some manufacturers adopt new spring material evading broken. The lose match of rotor and axis of pump also result in no delivery or inefficient discharge. This situation will be overcome by changing rotor. After the above check and examine still find any rotor stuck or overflow valve abnormal, it is suggestive that vane abrasion is extensive, broken and spring damaged. Much abrasive vane can not successfully segment high and low pressure area, resulting no delivery or inefficient discharge as the areas exchange. The broken vane or spring not only cause flow trouble but also increase noise as whole. Furthermore, if they flow into other inner components may result in new failure. The solution to this is to change new vane or spring and clean out broken piece. fuel dispenser It is suggestive that change all vanes if fuel dispenser have operated long time. Changing a new pump overcomes too large abrasion between frame and rotor. To check whether a leakage occurred in pine between fuel dispenser and tank, different diameter of pipe connection, bottom valve stuck or leakage. Abnormal noise and vibration The reason of fuel dispenser

ashing　　32 Tyre dressing Applies tyre dressing at the end of the wash　　33 Tyre sprayer Sprays each tire individually　　34 Tyre white wall cleaner Applies white wall cleaner to the tyre　　September 2005 IFSF - STANDARD FORECOURT PROTOCOL Version 1.33　　 CAR WASH SPECIFICATION　　 Page: 65 of 65　　35 Under fuel dispenser chassis sealant Applies rust inhibitor to the underside of the vehicle　　36 Under chassis wash Sprays the under chassis with water　　37 Van Chemical Applies special vantruck chemical　　38 Wax cold Applies cold wax to the vehicle　　39 Wax cold foaming Applies cold foaming wax to the vehicle　　40 Wax hot Applies hot wax to the vehicle　　41 Wax hot foaming Applies hot foaming wax to the vehicle　　42 Wax polish foaming Applies foaming wax for polishing the vehicle　　43 Wax sealer Applies sealer wax to the vehicle　　44 Wax triple foaming Applies triple colour foaming wax to the vehicle　　45 High pressure during brush Applies high pressure water jets with the brushes　　46 Dryer side contoured Drying with contoured side nozzles　　47 Side HP contoured Side High Pressure wash that profiles the vehicle s side　　48 fuel dispenser Van Side HP Side High Pressure wash that profiles the vehicle s side　　49 Wheel scrub with HP Wheel wash brush with High pressure spray　　50 Triple Foam Detergent Uses a 3 colour detergent to wash the vehicle　　51 Tyre rim cleaning doub fuel dispenser

frica s magic that transformed modern art Feb 9th 2006 | JOHANNESBURG From The Economist print edition An exhibition in South Africa reveals the depth of African influence on Picasso PABLO PICASSO never went to Africa. But more than three decades after his death, his art is travelling to the continent that so deeply affected his work. “Picasso and Africa� the most extensive exhibition of the artist s work ever assembled in the region, was due to open at the Standard Bank Gallery in Johannesburg on February 10th, and will travel to the Iziko South Afri fuel dispenser can National Gallery in Cape Town in April. The show, which highlights Africa s influence on Picasso s work, brings more than 80 of his paintings, drawings and sculptures together with a selection of African masks and statues similar to those that he had around him as he worked. Picasso said that the “virus�of African art stayed with him throughout his life. He caught it in June 1907, when stumbling upon the African and Oceanic collection at the Ethnographic Museum of the Trocadéro in Paris. The fateful encounter was a revelation “The masks were not simply sculptures like any other. Not at all. They were magical objects.�That day, he later said, he Out of Africa understood what painting really meant. “It is not an aesthetic process; it s a form of magic that interposes itself between us and the hostile universe, a means of seizing power by imposing a form on our terrors as well as on our desires.� He had been working on “Les Demoiselles d Avignon� which became one of his most famous paintings. The visit to th fuel dispenser e museum gave him the answers he had been looking for. This portrait of five prostitutes, which he described as his first “exorcism painting� was his first work to bear signs of African influence, with two of the women s faces shown as African masks. Many other signs were to follow. The exhibition shows how Picasso absor fuel dispenser